Although using hanging baskets for exterior wall construction is convenient and fast、 safety management is also very strict. Due to the high risk of exterior wall decoration construction、 safety inspection of hanging basket construction is crucial. This article briefly summarizes the content of hanging basket safety management and hanging basket safety inspection as follows:

1. During the construction process of exterior wall using high-altitude operation hanging baskets、 the hanging basket safety inspection work should be serious and careful、 paying attention to every detail、 and checking whether the hanging basket safety rope is in place on site、 The safety belt of construction personnel must be tied to the safety rope and the safety belt buckle must be checked for security. There should be no more than two operators inside the hanging basket、 and they should wear safety helmets and fasten safety belts correctly. Safety belts are strictly prohibited from hanging on the hanging basket frame to avoid accidents. It is strictly prohibited to place flammable and explosive materials such as oxygen cylinders and acetylene cylinders in the hanging basket Before the construction of the hanging basket、 a special construction plan for the hanging basket for high-altitude operations should be prepared based on the characteristics of the project、 and relevant approval work should be done well. For hanging baskets that cannot be installed according to the equipment manual due to objective conditions、 the user unit shall organize expert argumentation as required. Installation and construction can only be organized after the scheme argumentation is approved 3. When the hanging basket equipment enters the site、 it is necessary to submit the factory inspection report、 certificate of conformity、 and equipment operation manual of the hanging basket equipment for review and inspection After the installation of the hanging basket、 a third-party testing agency with testing qualifications should be entrusted to test each hanging basket、 and the testing agency should issue a testing report. Only when qualified can it be used After the installation of the hanging basket、 it should be inspected according to the special construction plan and user manual to check whether the installation model matches and whether the installation method meets the requirements. And compare and inspect the specifications and models of various accessories of the hanging basket equipment、 measure the spacing between the front and rear brackets and the length of the extended cantilever according to the product manual、 and ensure that the height and height difference of the front and rear brackets meet the requirements specified in the product manual 6. The heavy weight hanging from the lower end of the safety wire rope auxiliary rope of the hanging basket must be above the ground、 with a height of 100mm~200mm、 and should be in a free state. Check whether the binding method is secure 7. Each hanging basket must be equipped with a life-saving safety rope、 which should be fixed to the building structure with sufficient strength. It is strictly prohibited to fix the safety rope to the suspension mechanism or bracket. In places without reliable binding points、 two safety ropes、 the main and auxiliary、 must be installed. The safety rope must be whole and there should be no joints. Anti wear measures should be taken at the corners of the wall and other parts of the safety rope、 Rubber products (such as bicycle inner tubes) can be used for padding 8. The upper limit stop (trigger) device、 namely the height limiter、 must be complete and intact、 and must be installed on the auxiliary rope、 800mm below the boom head 9. The safety lock involved in the hanging basket should be sent to a qualified inspection and testing agency for calibration. The validity period of calibration should comply with the product manual、 generally not exceeding 1 year. The calibration label should be pasted in a prominent position of the safety lock、 and the safety lock must be unlocked and locked flexibly and reliably. The safety lock calibration nameplate and testing calibration report should be consistent 10. The upper limit travel switch of the hanging basket must be complete、 intact、 sensitive、 and reliable. Before use、 debugging and inspection must be carried out to ensure construction safety 11. The hanging basket weight block must have a weight label、 usually 25 kilograms per unit、 and the weight must meet the label requirements. The number of weight blocks must meet the requirements、 and the missing edges、 corners、 and fractures of the weight blocks must be replaced. The weight blocks must be securely tied and locked、 and anti movement measures should be taken 12. The front bracket of the hanging basket suspension mechanism must not be supported on the parapet wall、 outside the parapet wall、 or at the edge of the cantilever structure. The outer side of the hanging basket arm must be higher than the inner side 13. A steel wire rope commonly used for hanging tools must be installed inside the basket、 and materials cannot be hung outside the basket During the construction process of the hanging basket、 operators enter and exit the basket from the ground. Before construction、 the basket must be on the ground、 and the distance between the two baskets should be 0.5m

15. The height and spatial dimensions of the hanging basket frame should meet the requirements of the product manual、 and a baffle with a height of no less than 18cm should be installed at the foot of the basket frame 16. The hanging basket distribution box must be equipped with legs、 and the center of the box should be kept at a certain height from the ground、 The wiring of the distribution box must comply with the standard requirements of "one machine、 one switch、 one leakage、 and one box". The box should be equipped with system wiring diagrams、 branching marks、 and electrician inspection records. Cables should not be dragged on the ground、 and protective measures should be taken when crossing walls and roads.

17. Personnel engaged in hanging basket installation and dismantling as well as construction personnel must hold a certificate、 and the installation and dismantling personnel should hold a valid "Construction Special Operation Qualification Certificate" (the type of work is "hanging basket installation and dismantling worker") Only then can one start work Before installing/dismantling the hanging basket、 the safety supervision agency of the project should be informed of the installation/dismantling situation After the hanging basket has undergone self inspection and passed the inspection by the legal testing unit、 the hanging basket leasing unit、 the construction general contracting unit、 the supervisor、 etc. shall jointly inspect and accept the hanging basket. The hanging basket leasing unit shall provide written instructions on safe use and management to the user unit、 and handle the handover procedures

Function of testing report:

1. Project bidding: Issue authoritative third-party CMA/CNAS qualification report

inspection and testing process:

1. Telephone communication and confirmation of requirements

Testing and testing characteristics:

1. The testing industry is fully covered、 meeting different testing needs

3. Engineers provide one-on-one services to make testing more accurate

4. Free initial testing、 with no testing fees charged

5. Self service order delivery for free on-site sampling